DISSOLVES SLUDGE THAT BUILDS UP IN HEAT EXCHANGERS: HEAT EXCHANGER CLEANER is a liquid POLYMER - Acidic based new generation material that readily dissolves sludge that builds up in heat exchangers.

TECHNICAL PROPERTIES:
Composition: Liquid
Appearance: Clear Colorless to charasteristic
Recommended Concentrations: 50-100% by volume
Recommended Temperatures: Ambient

DESCALANT is specially formulated to clean and remove scale and microorganism as well as the growth of algae, humus, mussels, shellfish etc and also effectively dissolve magnetite, lime, rust and other deposits from water systems, Descalant most commonly used to clean heat exchangers and centrifugal separators.

Dosage

HEAT EXCHANGER CLEANER:

PRETREATMENT TECHNICAL DATA SHEET:

USE & CONTROL INSTRUCTIONS:
Operating Properties (Typical):

Specific process conditions may warrant operating the above parameters outside of the typical ranges. Please consult your RX MARINE representative:

Charge Instructions:
HEAT EXCHANGER CLEANER is used as delivered at ambient temperatures. If time is not a factor in the clean out, the solution can be diluted up to 50% with water.

Charge details:
1) If used at the 50% dilution: Fill the clean tank approximately ½ full with fresh water.
2) Set valves to proper setting for clean out
3) Plumb the circulating system to the correct side of the heat exchanger Turn on.
4) Slowly add 1 gallon of HEAT EXCHANGER CLEANER for every two gallons of  bath (or use the HEAT EXCHANGER CLEANER neat)
5) Allow to circulate for at least ½ hour dependent on sludge.
6) Turn off pump and disconnect plumbing from heat exchanger
7) Flush heat changer with fresh water to remove residual acid.
8) Turn heat exchanger valves back to running positions.
It is important to circulate the solution through the heat exchanger for at least 30 minutes. The cleaning time will vary depending on the amount and type of sludge build-up. After the heat exchanger is cleaned, it is highly recommended that the  unit  be  flushed with water. If this step is not taken, an increase in the free acid of the operating phosphate solution might occur.

PRETREATMENT TECHNICAL DATA SHEET:

Analysis Procedures:
CAUTION: DO NOT PIPETTE BY MOUTH ::: Free Acid
Equipment needed:::
• Burette Assembly
• 5-ml pipette and bulb
• 250-ml flask or beaker
• 100 ml graduated cylinder

Reagents needed:::
• Bromophenol Blue indicator
• 1.0N Sodium Hydroxide

Free Acid Procedure:
1. Using a pipette, pipette 5-ml of your solution into a 100-ml graduated cylinder. Fill the cylinder to the 100 ml mark with DI or RO water, then mix by up ending 2-3 times.

2. Pipette 5 ml of the above dilution to a beaker or flask; add 4-5 drops of Bromophenol Blue indicator. Then add 1.0N Sodium Hydroxide drop-wise until the
solution changes from yellow to blue. Record the number of mls as points of Free Acid.

The concentration is calculated by multiplying the points of Free Acid times the HEAT EXCHANGER CLEANER factor 0.59. This equals the concentration in percent by volume
of HEAT EXCHANGER CLEANER in solution. Points of Free Acid X 59 = Percent by volume of HEAT EXCHANGER CLEANER

PRTREATMENT TECHNICAL DATA SHEET:

Notes

Equipment:
The HEAT EXCHANGER CLEANER is used for cleaning Stainless steel heat exchangers.The external pump and circulating system employing the HEAT EXCHANGER CLEANER should likewise be made of stainless steel or of a suitable, non-corrosive plastic.

Useful area

Secondary Heating System Cleaner and Scale Remover

Major Industrial Cleaning Applications

1. Heat Exchanger Cleaning Chemical

Heat exchangers can accumulate:

• Mineral scale

• Rust and iron oxide

• Sludge

• Oil and grease

• Process deposits

• Carbonaceous contamination

• Water-side deposits

RXSOL provides different cleaning chemicals depending on the type of deposit, equipment metallurgy and cleaning method.

For example, RXSOL lists Heat Exchanger Cleaner RXSOL-16-1681-025, along with dedicated heat-exchanger products such as Heat Exchanger Cleaner Caus and Heat Exchanger PhosClean. (Rxchemicals)

For rust and corrosion deposits, RXSOL also offers a rust-removal product intended for suitable evaporators, heat exchangers and boilers. (RxMarine)

2. Thermic Fluid System Cleaning Chemical

Thermic-fluid heating systems may develop deposits resulting from:

• Thermal degradation

• Oxidation

• Carbonaceous deposits

• Sludge

• Oil contamination

• Circulation problems

RXSOL cleaning chemistry can be selected according to the thermic-fluid type, deposit condition and system construction.

Before chemical cleaning, the existing thermic fluid should be identified and the system evaluated for compatibility.

3. Steam Boiler Coil Cleaning Chemical

Steam boilers and heating coils can develop scale, rust, sludge and corrosion deposits, particularly when water treatment and operating conditions allow deposits to accumulate.

RXSOL offers products for boiler maintenance and scale/corrosion control, including Corrosion Scale Treatment Boiler – RXSOL-42-4029-025, sludge-conditioning products and specialized scale-removal chemistry. (Rx Solutions)

The correct chemical should be selected based on whether the contamination is primarily:

• Calcium scale

• Silica/silicate scale

• Iron oxide/rust

• Oil contamination

• Sludge

• Mixed deposits

4. MS Tank Cleaning Chemical

Mild-steel tanks may require chemical cleaning before:

• Inspection

• Maintenance

• Repainting

• Product changeover

• Commissioning

• Repair

• Storage of a new product

RXSOL cleaning products can be selected for oil, grease, hydrocarbon, rust, scale and general industrial contamination.

For tank cleaning, the chemical selection should always consider the previous cargo or stored material.

5. MS Pipeline Cleaning Chemical

RXSOL chemicals can be used in suitable pipeline-cleaning programs for removing:

• Rust

• Scale

• Oil

• Grease

• Sludge

• Process deposits

• Hydrocarbon residues

Pipeline cleaning can be carried out by suitable circulation, soaking, flushing or recirculation methods, depending on the pipe diameter, deposit and available equipment.

RXSOL Chemical Selection by Deposit

RXSOL's product range includes a silica-scale remover specifically described for heat exchangers, condensers and boiler tubes. (Rx Solutions)

Chemical Cleaning Method

A typical industrial cleaning program may include:

Inspection → Deposit identification → Pre-flushing → Chemical circulation/soaking → Monitoring → Drainage → Water rinsing → Inspection → Neutralization/passivation where applicable

The exact concentration, temperature and contact time should not be selected from a generic internet recommendation. They should be established from the applicable RXSOL TDS/SDS and the equipment manufacturer's requirements.

For example, certain RXSOL tank/heat-exchanger cleaning procedures use recirculation with controlled temperature and subsequent thorough water rinsing. (Scale Remover)

Why Deposit Identification Is Important

There is no single cleaning chemical that is automatically suitable for every industrial deposit.

For example:

Calcium carbonate scale ≠ silica scale ≠ rust ≠ oil sludge ≠ carbon deposit.

Using the wrong chemical can result in poor cleaning or unnecessary risk to:

• Mild steel

• Stainless steel

• Copper

• Brass

• Aluminum

• Rubber seals

• Gaskets

• Coatings

• Linings

Therefore, RXSOL recommends selecting the cleaning chemical according to the deposit and metallurgy.

RXSOL Chemical Supplier in Panvel & Navi Mumbai

RXSOL chemical products are available for industrial customers in the Panvel, Taloja, Kalamboli, Kamothe, Navi Mumbai and surrounding industrial areas.

RX CHEMICAL RXSOL RX MARINE is listed in the MIDC Pawane/TTC Industrial Area of Navi Mumbai, while other chemical businesses are located across the Panvel–Taloja industrial belt.

Industries Served

RXSOL cleaning chemicals can be considered for:

• Chemical plants

• Pharmaceutical industries

• Process industries

• Manufacturing units

• Boilers and steam systems

• HVAC and cooling systems

• Heat-exchanger maintenance

• Oil and gas facilities

• Marine industries

• Engineering workshops

• Storage terminals

• Tank farms

• Industrial utilities

Frequently Asked Questions

What chemical is used for heat exchanger cleaning?

The appropriate chemical depends on the deposit. RXSOL has dedicated heat-exchanger cleaners and separate chemistry for rust, mineral scale, silica scale and oily contamination. (Rx Solutions)

Which chemical is suitable for boiler coil cleaning?

The selection depends on whether the boiler coil contains mineral scale, silica, rust, sludge or another deposit. RXSOL offers dedicated boiler and scale-treatment products. (Rx Solutions)

Can RXSOL chemicals clean mild-steel tanks?

Suitable RXSOL tank-cleaning and rust/scale-removal products can be selected for MS tanks depending on the contamination and condition of the tank.

Can RXSOL chemicals clean industrial pipelines?

Yes, suitable RXSOL cleaning chemistry can be selected for pipeline descaling, rust removal, degreasing or sludge removal depending on the deposit and pipe material.

Do you supply chemicals in Panvel?

RXSOL chemicals can be supplied to industrial customers in Panvel, Taloja, Kalamboli, Kamothe and Navi Mumbai, subject to product availability and packaging.

RXSOL Brand Chemical Supplier

For heat exchanger cleaning, thermic fluid system cleaning, steam boiler coil cleaning, MS tank cleaning and industrial pipeline cleaning, share the following information with the chemical enquiry:

Equipment: Heat exchanger / boiler / thermic-fluid system / tank / pipeline
Material: MS / SS / copper / aluminum / other
Deposit: Scale / rust / oil / sludge / carbon / mixed
Equipment capacity: ___
Cleaning method: Circulation / soaking / spray / CIP
Temperature: ___
Previous chemical/product: ___

Industrial area

Supply location

Heat Exchanger Cleaner manufacturer supplier distributor in Mumbai, Kandla, Kolkata, Vizag, Chennai, India, Fujairah, Dubai UAE, Muscat Oman, Kenya Africa. Get the best quality of Heat Exchanger Cleaner at a competitive price from us. We have ready stock of Heat Exchanger Cleaner in India, UAE Gulf, Oman, Kenya Africa. Contact us for bulk as well as small orders.

Generic name

Keywords

RXSOL chemical supplier Panvel, RXSOL chemical supplier Navi Mumbai, heat exchanger cleaning chemical Panvel, heat exchanger descaling chemical Navi Mumbai, thermic fluid cleaning chemical Panvel, boiler coil cleaning chemical Panvel, steam boiler cleaning chemical Navi Mumbai, MS tank cleaning chemical Panvel, mild steel tank cleaner, pipeline cleaning chemical Panvel, industrial descaling chemical Taloja, boiler descaler Taloja, heat exchanger cleaner Taloja, industrial cleaning chemicals Panvel, RXSOL supplier Taloja, RXSOL industrial chemical supplier Maharashtra.

The wording above deliberately avoids claiming that one chemical cleans every type of heat exchanger, thermic-fluid system, boiler, tank and pipeline; the RXSOL product range itself contains different cleaners for different deposits and applications. (Rx Solutions)