Degreaser HCF solvent

Degreaser HCF solvent is a tank cleaning additive which has proved to be extremely effective as hydrocarbon and contaminant remover for tanks preparing and solvents loading.
Degreaser HCF solvent Quickly removes oil, grease, gimres, adhesive and dyes. Best results also achieved forcleaning of oil side of fuel and lube oil heat exchangers. Used  as  a tank cleaner or for general degreasing , cleaning and gas freeing for double bottom tanks, wing tanks, tank lines, fuel oil tanks, etc .

Product Properties

 Used as a tank cleaner or for general degreasing, cleaning and gs freeing for double bottom tanks, wing tanks, pipe lines, fuel oil tanks, etc.
 

Tank Lining –     Stainless / Zinc / Epoxy / Phenolic.

Dosage

DIRECTION FOR USE & DOSAGE INSTRUCTION

Spraying Method : 
For cleaning on surface with heavy contaminants, it will be more effective to spray on the area with a high pressure sprayer. Wet the entire surface with neat Degreaser HCF solvent and allow 10~ 15 minutes for the solution to take effect before washing off the entire area with water at ambient temperature.

Circulation Method:
5% of Degreaser HCF solvent can be circulated by using the deep well pump through tank washing machine for approximately 5 hours at a temperature of between 40~ 45°C. The solution can be transferred to another tank for washing. The treated tank had to be cleaned thoroughly with water.

Immersion Method:
Small parts / components may be cleaned by soaking them in a bath of Degreaser HCF solvent at a dosage of 5-8% of solution in water.

Useful Area

Tank Cleaner effectively cleans Oil Residue and Sludge from tanks which is compulsory prior to repair tank.

Industrial Usage

#TankCleaner_ShipChandler
#TankCLEANINGchemical_supplier
#TankClean_MumbaiDubaiMuscat

Bulletin Details

TANK CLEANER S

Code: RXSOL-20-2001-222

Tank Cleaner and Degreaser

RXSOL-20-2001-222 Introduction (Solvent based oil and grease remover ) Highly concentrated solvent emulsifier, with powerful penetrating  agent corrosion inhibitor  and  surfactants,  RXSOL-20-2001-222  is  used  as  a tank cleaner or for general degreasing , cleaning and gas freeing for double bottom tanks, wing tanks, tank lines, fuel oil tanks, etc .
 

Tank Lining – Stainless / Zinc / Epoxy / Phenolic.
Using-Procedure    

Spraying:–

This can be beneficial as part of the initial cleaning process after the carriage of Lube oils and Lube oil additives.  As soon as the tank in question has been checked empty by the attending surveyor, RXSOL-20-2001-222  should be sprayed over all surfaces which are safely reacheable.
 

Portable machines:–

After 45 minutes the butterworth machines should be operated for 3 x 20 minutes drops using warm 60o C, then the machines brought back to the top and a full hot wash 80 – 85 o C should be carried out for at least 6 hours.

Fixed machines:–

Wash ambient for 45 minutes followed by warm water for one cycle before increasing to hot (80oC) for 4 hours.

Injection:–

This can be carried out by injecting RXSOL-20-2001-222  into the butterworth system after the heater. A normal amount to use would be 100 – 150 liters during the initial washing cycle.  Water temperature should be 60o C during the injection period then brought up to 80 – 85 o C for the full washing period.

Re-circulation:–

Possibly the best result are achieved by re-circulating a solution of RXSOL-20-2001-222 after the initial rough washing of the tank.  A sufficient amount of fresh water to maintain good suction should be heated  to 60 o C and approximately 420 liters of RXSOL-20-2001-222  (2 drums) added for each 500 liters of fresh water.  The temperature of the mixture can be increased depending upon  the melting point if the product being cleaned.  The solution should be circulated for at least 4 hours and the butterworth machines  operated at maximum pressure in all areas of the tank  throughout this process.  If a number of tanks are to be circulated, then a substantial quantity of solution can be made so that transfers can be made without delay and any small amounts lost will not affect the operation.  Normally following transfer to another tank, 100 liters RXSOL-20-2001-222  is added for each 5000 liters of solution.  This is called “spiking”.
  

Following the re-circulation process, the tank must be hot butterworthed 80-85o C for at least 6 hours.
      *Use         a                 strainer                at               the                 pumpstack               when               circulating          any                        solution              RXSOL-20-2001-222 is recommended for local cleaning and degreasing and may be applied  by  brush,  hand  spray, immersion, soaking or any other conventional means. Apply concentrate RXSOL-20-2001-222 over  soiled  area  and wait for 20-30 minutes before rinsing off with water.
 

Soak Method:-

For heavy oil and soil Put parts to be cleaned into a bath of concentrate RXSOL-20-2001-222 and  for medium to light soiling use a solution of 10-30% RXSOL-20-2001-210 in water. Parts should be soaked for at least  30 minutes  before washing off with water.

Spray-Method:-

Spray concentrate  RXSOL-20-2001-222  over all soiled areas.  With in  15  and  30   minutes,  RXSOL-20-2001-222 starts   its function then rinse off by water hose. For stubborn deposits, agitation by scrubbing will  assist  the  cleaning operation .

Cargo Tank Cleaning after Mineral Oils

Direct injection method:–

Make  a   solution  of  RXSOL-20-2001-222  between   0.1  and  2.0%   i.e.   one   to    twenty    litres    per  ton   wash water.   Then      use     with     Tank     cleaning      machine ,    Best     results    are     obtained   when   water  is    heated  to  a     temperature      between          60  to  80°C.  Slops Should              be             Constantly              Stripped       from, tank.                                                   

Recirculation method / Ship's Rocking Mottion:– 

Make  soln.  Strength  with RXSOL-20-2001-222 between  0.5 –3 %  and  used  with  Tank Cleaning machines OR fill the tank to 20-30% volume with sea water and add the RXSOL-20-2001-222 up to full dose  . For better  results  heat  the solution  between 60 - 80°C.

NOTE :Dose rate and results will vary depending on amount of contamination.

Spot cleaning- RXSOL-20-2001-222  (concentrate) can be sprayed over surfaces and left  for  20 - 30 minutes  Finally wash down the tank surfaces with hot  water between 60°C and 80°C with  high  pressure   machine .   Keep stripping tank slops and transfer to holding tank/slop tank.Cleaning  of  theOil  side of  Lube  Oil Heat Exchangers  Cleaning  is  best  achieved  by the recirculation method using a heated 20% solution of RXSOL-20-2001-222.
1) First of all drain off any remaining oil from Heat Exchanger.
2) Connect the discharge side of a portable pump to the lower heat exchanger connection & the suction Side of the pump to the bottom outlet of a 200 litre drum.
3) Complete the circuit by connecting the upper connection on the heat exchanger to the top of the drum.
4) Maintain the bath temperature between 60-80 0 C throughout the cleaning operation.  If it is not possible to heat, the operation will need to be extended.
5) Use the pump to maintain circulation for 12 to 15 hours.  When the cleaning is completed, disconnect the lower heat exchanger connection and drain out the cleaning solution.
6) Connect a fresh water supply to the upper heat exchanger connection, and rinse until the water runs clean from the lower connection.                                                                                                                                                                                                                                                              When rinsing is complete, disconnect the water supply and thoroughly drain and dry the heat exchanger

Product Properties

   
                     **Used as a multi-purpose degreaser in extremely hard cleaning conditions**

Characteristics
  It is cost effective, easy to apply and use.
• High emulsification on mineral oils and petroleum based chemicals.
• Safe to use on most metal surfaces, painted surfaces and tank coatings.
• Cleans oil coolers, fuel oil pre heaters and lube oil heat exchangers.
• Removes general oil contamination from machinery and engine room.
• Economical  cost effective  .  

**For detailed  information  on  safety  & health, Please  refer  to  Material  Safety  Data Sheet & /or Product Label**

Remarks

Using-Procedure    

Spraying:–

This can be beneficial as part of the initial cleaning process after the carriage of Lube oils and Lube oil additives.  As soon as the tank in question has been checked empty by the attending surveyor, RXSOL-20-2001-210  should be sprayed over all surfaces which are safely reacheable.
 

Portable machines:–

After 45 minutes the butterworth machines should be operated for 3 x 20 minutes drops using warm 60o C, then the machines brought back to the top and a full hot wash 80 – 85 o C should be carried out for at least 6 hours.

Fixed machines:–

Wash ambient for 45 minutes followed by warm water for one cycle before increasing to hot (80oC) for 4 hours.

Injection:–

This can be carried out by injecting RXSOL-20-2001-210  into the butterworth system after the heater. A normal amount to use would be 100 – 150 liters during the initial washing cycle.  Water temperature should be 60o C during the injection period then brought up to 80 – 85 o C for the full washing period.

Re-circulation:–

Possibly the best result are achieved by re-circulating a solution of RXSOL-20-2001-210 after the initial rough washing of the tank.  A sufficient amount of fresh water to maintain good suction should be heated  to 60 o C and approximately 420 liters of RXSOL-20-2001-210  (2 drums) added for each 500 liters of fresh water.  The temperature of the mixture can be increased depending upon  the melting point if the product being cleaned.  The solution should be circulated for at least 4 hours and the butterworth machines  operated at maximum pressure in all areas of the tank  throughout this process.  If a number of tanks are to be circulated, then a substantial quantity of solution can be made so that transfers can be made without delay and any small amounts lost will not affect the operation.  Normally following transfer to another tank, 100 liters RXSOL-20-2001-210  is added for each 5000 liters of solution.  This is called “spiking”.
  

Following the re-circulation process, the tank must be hot butterworthed 80-85o C for at least 6 hours.
      *Use         a                 strainer                at               the                 pumpstack               when               circulating          any                        solution              RXSOL-20-2001-210 is recommended for local cleaning and degreasing and may be applied  by  brush,  hand  spray, immersion, soaking or any other conventional means. Apply concentrate RXSOL-20-2001-210 over  soiled  area  and wait for 20-30 minutes before rinsing off with water.
 

Soak Method:-

For heavy oil and soil Put parts to be cleaned into a bath of concentrate RXSOL-20-2001-210 and  for medium to light soiling use a solution of 10-30% RXSOL-20-2001-210 in water. Parts should be soaked for at least  30 minutes  before washing off with water.

Spray-Method:-

Spray concentrate  RXSOL-20-2001-210  over all soiled areas.  With in  15  and  30   minutes,  RXSOL-20-2001-210 starts   its function then rinse off by water hose. For stubborn deposits, agitation by scrubbing will  assist  the  cleaning operation .

Cargo Tank Cleaning after Mineral Oils

Direct injection method:–

Make  a   solution  of  RXSOL-20-2001-210  between   0.1  and  2.0%   i.e.   one   to    twenty    litres    per  ton   wash water.   Then      use     with     Tank     cleaning      machine ,    Best     results    are     obtained   when   water  is    heated  to  a     temperature      between          60  to  80°C.  Slops Should              be             Constantly              Stripped       from, tank.                                                   

Recirculation method / Ship's Rocking Mottion:– 

Make  soln.  Strength  with RXSOL-20-2001-210 between  0.5 –3 %  and  used  with  Tank Cleaning machines OR fill the tank to 20-30% volume with sea water and add the RXSOL-20-2001-210 up to full dose  . For better  results  heat  the solution  between 60 - 80°C.

NOTE : Dose rate and results will vary depending on amount of contamination.

Spot cleaning- RXSOL-20-2001-210  (concentrate) can be sprayed over surfaces and left  for  20 - 30 minutes  Finally wash down the tank surfaces with hot  water between 60°C and 80°C with  high  pressure   machine .   Keep stripping tank slops and transfer to holding tank/slop tank.Cleaning  of  theOil  side of  Lube  Oil Heat Exchangers  Cleaning  is  best  achieved  by the recirculation method using a heated 20% solution of RXSOL-20-2001-210.
1) First of all drain off any remaining oil from Heat Exchanger.
2) Connect the discharge side of a portable pump to the lower heat exchanger connection & the suction Side of the pump to the bottom outlet of a 200 litre drum.
3) Complete the circuit by connecting the upper connection on the heat exchanger to the top of the drum.
4) Maintain the bath temperature between 60-80 0 C throughout the cleaning operation.  If it is not possible to heat, the operation will need to be extended.
5) Use the pump to maintain circulation for 12 to 15 hours.  When the cleaning is completed, disconnect the lower heat exchanger connection and drain out the cleaning solution.
6) Connect a fresh water supply to the upper heat exchanger connection, and rinse until the water runs clean from the lower connection.                                                                                                                                                                                                                                                              When rinsing is complete, disconnect the water supply and thoroughly drain and dry the heat exchanger

Supply Locations

Tank Cleaner HD RXSOL manufacturer and supplier in Mumbai, Kandla, Mundra, Hazira, Chennai, Kolkata, Buz Buz, Visakhapatnam, Gangavaram, Haldia, Paradip, Nairobi, Kenya, Africa, Fujairah, Sharjah, Ajman, Abudhabi, Dubai UAE GULF Middle East, Muscat Ruwi Ghala Barka, Oman Sohar, Yemen, Sudan