Aqua Sol Break Degreaser

3 Pieces of Good Advice:
Apply  RXSOL solution on dry surface where possible! A dry surface will absorb far better than a wet surface. When applying RXSOL on vertical surfaces: Start application from the bottom and work upwards! If beginning from the top and going downwards, the RXSOL may produce "channels" down the surface, thereby running too fast off the surface. During high pressure cleaning: It is important that the rinsing water does not run over non-cleaned surfaces! The rinsing water can draw soap from the surface if running over non-cleaned surfaces. High pressure together with optimum concentration of RXSOL will give the best effect .

Applications:-RXSOL Suitable for cleaning of  hard surfaces, such as Decks, Tanks, HOLD,  etc. can be used for all  types of cleaning and degreasing and  may be applied by brush, handspray, high and low pressure washing machines etc.

The Importance of HIGH FOAM  by High-Pressure Cleaning

The job of high pressure cleaning can be done easier & quicker by simply using RXSOL correct dosages. Using a high pressure cleaner alone, without any CLEANER, will not  achieve  optimal cleaning results High-pressure cleaning primarily refers to cleaning of Hard  surfaces, such  as Decks, Tanks, Engine-rooms, etc. and in the majority of cases the cleaning is done according to the so-called two-step method:

Step 1:  Spraying the  RXSOL solution over the area to be cleaned.
Step 2:   Washing down the area using a high-pressure water jet.

After the solution has been  sprayed on the surface and  before the wash down begins, the chemicals penetrates & thoroughly moistens dirt & other grime. During wash down, the RXSOL thoroughly dissolves the particles of dirt, even oil and fat, in the water spray and thus achieves optimal cleaning results.In addition to being more effective, the use of RXSOL substantially reduces the time required for the Cleaning operation, as well as preventing dirt from reforming on the surface. The use of RXSOL in correct dosages is half the job done.

Dosage

Heavy Soil deposition                    Use Undiluted from to 20-50% diluted with water. 
Medium soil deposition                 10-20%  diluted with water. 
Light Soil ( general degreasing )   5-10% diluted with water.

General Cleaning:- This can be used for all types of cleaning &  degreasing & may  be applied by  Brush, Hand spray, high and low pressure washing machines etc. Time necessary for cleaning depends on the nature and  thickness of the deposits. 20-30 min. will suffice for   most applications. Hardened, carbonised or aged deposits may require up to 4 hours. If  the cleaning  solution is not heavily contaminated, it may be re-used at a later stage. If allowed to cool, the de-gassing procedure must be repeated. Depending on degree of contamination RXSOL should be mixed with warm water at a rate of 50-200 ml   per 10 litres. i.e. 1 cup of RxTuff to a bucket of water. RXSOL solution can  be applied  simply by mops, brushes or rags, or by dipping the soiled articles into  the RXSOL solution. After cleaning, rinse off with cold or warm water. Due to high foaming properties, RxTuff is not recommended for washing machines.                        

Method of Application and Dose Rates:-

• Direct injection method for pressure washing machines. Dose rate 1-5 litres per ton wash water (0.1-0.5%).
• Spot cleaning. Hand spray neat or diluted with up to 5 parts water and leave for several minutes before rinsing off with clean water.

Cleaning of Cargo HOLD Systems:-

• Spray RXSOL  on with a high pressure cleaning machine and  use 1:6 with water. If used with hand sprayer, spray  the product  neat onto the surface, allowing 1 lit. for every 12 m2. Use a 5-8% solution in a tank washing machine.
• Leave for about 30-45 minutes. The surface should be kept wet.
• Wash down with hot water (80°C) and check the cargo tank.
• Repeat the procedure if necessary.

Note:- For tuff cleaning spray 10-20 %  concentration  to  the surfaces to be cleaned. Allow to  penetrate for 20 minutes and flush off. For deposits  which are very hard to remove, increase the concentration to 50% and repeat if necessary.

Generic name